How do I change the lock on my Maytag washer

Door Locked at the end of the Cycle If the washer will not unlock at the end of a wash cycle, unplug the washer or disconnect power. Wait approximately 2 minutes for control to reset. Reconnect power to washer (plug in). Run a “Drain and Spin” cycle.

How do I reset my Maytag washer lock?

Door Locked at the end of the Cycle If the washer will not unlock at the end of a wash cycle, unplug the washer or disconnect power. Wait approximately 2 minutes for control to reset. Reconnect power to washer (plug in). Run a “Drain and Spin” cycle.

What are the codes for a Maytag washer?

Error CodeErrorSud or SdThere are too many suds in the washing machine.F5 E2The door is not locking properly.F7 E1Indicates a motor speed sensing error,F8 E1 or LO FLThe washer is sensing a low flow of water.

How do I reset the lid lock on my washing machine?

Make sure the washer is paused (press the Start/Pause button). During the spin cycle, this can take up to 3 minutes for the basket to stop spinning and allow you to open the lid.
Unplug the washer for a minute to reset.

How do I force my Maytag washer to unlock?

How to unlock Maytag washer door? If there are no errors with the washer and no components are faulty, you can try and cancel the wash cycle, press and keep holding the CYCLE END or CANCEL button and wait a few minutes and the door should unlock on its own.

Why is my Maytag washer keep lid locking?

This washer has sensors that detect the water supply and requires both hoses to have water going to the water valve. If it does not detect both water supply hoses are turned on, the control detects a problem with the water pressure sensor. The lid will lock, and the machine will enter a pump out mode for 8 minutes.

Where is the lid switch on my Maytag washer?

Lift the lid of the washer to release the old lid switch. I removed the two screws on the back of the control panel. The control panel then flips back. The switch is on the left side.

What's LF mean on a washer?

If F8 E1 or LF (too long to fill) appears in display, the washer is taking too long to fill.

Why is my Maytag washer lid not locking?

Common solutions for: Maytag Washer door or lid won’t lock If the door lock is defective, the washer door will not latch properly. … The door latch assembly might be defective. Inspect the door latch for damage. If the door latch is damaged, replace it.

What does F mean on Maytag washer?

Maytag F/02 – Drain Cycle Too Long The manufacturer has assigned this error or fault code to indicate that the washing machine drain cycle is taking too long. After 8 minutes of drain time the error code is displayed. … If that checks out, check to see if the drain pump or drain pump filter are clogged.

Article first time published on

What does error code Ld mean on Maytag washer?

“F32,” “Ld” or “C8” error codes indicate a slow or stopped drain pump, and “C6” indicates that the recirculation pump has stopped. Remove the pumps to access and remove the items clogging them. Unplug your Maytag Bravos washer from the electrical outlet.

How do I take the lock off my Maytag washer?

Touch “Cycle Signal” near the front-loading washer’s LCD control panel to deactivate the washer’s lock controls. The lock icon disappears from the LCD control panel when the lock control is off.

How do I turn off the LOC on my Maytag washer?

If you do not see the 3-2-1 countdown and are unable to de-activate Control Lock, try pressing the POWER button first, then touch and hold 3 seconds to de-activate control lock. If this does not work, try unplugging the machine or turning off the breaker for 1 minute, then power the machine back on and try again.

Will washer work without lid lock?

NO. The lid lock it to prevent injury to the people near the washer, as without it stopping the machine, the agitator will turn with the lid open. So. If you will open the top up, you should see the lid switch, and you should see the electric wires attached to it.

Why is my washer stuck on lid lock?

– Lock striker that presses down on the lid switch may be out of alignment. – A piece of lint or washing machine detergent has built up over time and hinders the locking of the lid. … – Actuator motor is faulty or has loose wiring (If washer is VMW = Vertical Modular Washer).

What does FL Lo mean on Maytag washer?

The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water. … Press the power button, and the washer will start a drain routine, which takes approximately 8 to 10 minutes, during which time the pump will run continuously. The control will not accept any input during this time.

What does F8 mean on washer?

If the washer has an F8 E1 error or LO FL error, the lid will be locked, and the control will be unresponsive. Press the power button, and the washer will start a drain routine which takes approximately 8 to 10 minutes, during which time the pump will run continuously.

What does FL Lo mean on a washer?

The Whirlpool washer Lo FL error code is displayed when water is not detected entering the washer or it’s not filling the washer fast enough. … Make sure the water supply hoses are not kinked or pinched and that screens in the supply line are clear of debris.

What does Code F 51 mean on a Maytag washer?

Mike, F 51 would indicate that the control board is not seeing the proper resistance on the motor circuit . You should check and make sure there are not any articles, stuck between the tubs, or under the agitator. Make sure you’re not overloading the machine and that you have proper voltage to the unit.

What is F2 in washing machine?

: The “F2” fault code indicates it’s taking too long to drain the tub of water in order to reset the pressure switch. The problem is that the washer is not always able to drain water so that the water level switch can reset.

What does E1 F9 mean on a Maytag washer?

If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. Check plumbing for correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub.

How do I fix error code 5d?

Reset error code 5d because, in certain cases, it occurs due to a failure. To solve the problem correctly, you need to press two times on PAUSE / CANCEL or 1 – on POWER, and then start washing. Stop the washer and take out items that are too bulky, soft, or fluffy. After that, continue the started cycle.

Why is my Maytag washer not draining?

Drain Hose Is Obstructed An obstructed drain hose is one of the most common reasons a Maytag washer won’t drain. Both kinks and blockages can obstruct the hose, preventing proper draining. A kinked hose can be gently straightened to restore function.

How do you remove the control lock on a Maytag washer?

Press the button for that dedicated key to activate and deactivate the Control Lock. To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.

Why does my Maytag washing machine say LoC?

If the control lock has been activated, the control will not function. If you try to push buttons, you may see the code “LoC” or “LC” (depending on your model). This is a reminder that you have set the control lock, and need to de-activate it to allow the washer controls to function.