How do I know what size gas struts I need

In general the length to choose for gas struts is about 55% of the height of the door you are trying to keep open. So if you have a door that is 1000mm in height a 550mm long gas strut would be about right. In simple terms we are talking half the door height plus a bit when determining optimal gas strut length.

Are gas struts measured open or closed?

The compressed length of a gas strut is when the gas strut is completely closed. Normally when the window or door is closed and can be measured pretty easily when a gas strut fails because it no longer has any Newton Meters (force) left in so the gas strut will be very easy to push closed.

How are gas springs measured?

The first type of gas springs are springs with welded mesh at either end. With this type of springs, we measure the total length from the centre of one mesh to the middle of the second mesh.

How are gas canopy struts measured?

Step 1 – Extended Length. Measure the gas strut from middle of end fitting to the middle of the end fitting when gas strut is fully extended.
Step 2 – Diameter. Measure across the Rod/Shaft. …
Step 3 – Newton Meters or Force. …
Step 4 – End Fittings. …
Step 5 – Order your Gas Strut.

How do you measure struts?

Co-Mac’s gas strut length is measured from the centre of the ball joint at each end. If you want to replace an existing gas strut, measure the length of your strut from the centre of each ball joint. If your gas strut does not have ball joints, measure the length of the gas strut with no end attachments.

How much pressure is in a gas strut?

4. How high is the pressure in a gas strut? The filling pressure of SUSPA gas struts depends on the extension force and the geometry and is between 10 and 230 bar. 5.

How do you measure for a gas spring lift?

Measure the Gas Strut when it is fully extended from the Centre of the End Fittings. …
Measure the Diameter of both the Barrel and the Rod. …
Measure the exposed Rod length from the Barrel to the centre of the End Fitting.

Are all gas struts adjustable?

All standard, shrouded, multi-positional and stainless-steel gas struts are available in a VARI‐LIFT version which can be adjusted to meet individual preferences as well as being adjusted in‐situ.

How do I select gas springs?

Decide what you want to use the gas spring for.
Enter the dimensions of the application.
Measure the thickness of the application.
Investigate which material the application is made of.
Determine the total weight of the application.
Determine the position of the pivot point.

How do you read a stabilus number?

The number is listed in the red square and consists of six digits or 4 digits and 2 letters. The number to the right is the pressure (here: 900N).

Article first time published on

How do you measure for cabinet struts?

Measure out from the edge of the door on the hinge side 2 1/2 inches and make a 2-inch-long mark across the side of the door. Measure perpendicularly along the first mark and make a mark at 1 inch. The point where the lines intersect is the center point of the bracket that holds the strut to the door.

What does N mean on gas struts?

It stands for Newton Meters and is a measurement of pressure. It essentially makes your gas strut work. Look for a N or Nm after a number on you Gas Strut…see below.

What are gas cylinder sizes?

Cyl. sizeDiameter × height, including 5.5 inches for valve and cap (inches)Water capacity (lb)A9 by 51 inches (230 mm × 1,300 mm)96B8.5 by 31 inches (220 mm × 790 mm)37.9C6 by 24 inches (150 mm × 610 mm)15.2

How is gas spring force calculated?

FORCE = (W x Y) / (Z x N) Y = Distance from fixed mounting point to center of the object (mm). Z = Distance from hinge point to moving mounting point (mm). N = Number of springs.

Can you adjust pressure on gas struts?

Fit the gas strut with the cylinder uppermost. The adjustment valve located at the uppermost end of the cylinder. Gas strut must be upright with the valve at the top and the rod pointing down during adjustment to avoid excessive loss of oil.