To reset, move the switch to ‘Off’ and then back to ‘Auto’. Wait for the relay to click (5 to 10 seconds). When the instant salt level is stable (and the negative sign still present), slide switch to ‘Super Chlorinate’ and back to ‘Auto’. It takes about 30 seconds for the unit to settle back on the default reading.
How do you recalibrate Hayward salt chlorinator?
Turn Salt System Off and On With the pump running, take the power switch down to the “Off” position, and then back up to “Auto”. You should hear a click within 10 or 15 seconds. When you do, press the diagnostic button five times in a row. The system will go through a recalibration process.
How do you reset inspect on Hayward?
If the Inspect Cell Light is the only LED light flashing, then you can reset it by simply holding down the diagnostic button for 3 seconds, then release. The Inspect Cell indicator will now reset and will later come back on after another 500 hours of use.
How do I know if my chlorine generator is working?
The easiest way to be certain if the chlorinator is working is to make sure the cell is clean by checking the needle or production lights on the chlorinator box. When operating, you should also see bubbles (hypochlorite gas) inside the chamber, producing what looks like cloudy water – that’s chlorine being created!How do I reset my Hayward Aqua Plus?
You must reset the system by entering the ‘Diagnostic Menu’ and then hitting the right arrow key once and then pushing the plus key once. This should reset the light and message.
How do you unclog a Hayward chlorinator?
To clear an air lock, remove the lid, then turn on the pump and allow the chlorinator to fill with water. Turn off the pump; replace the lid, and turn the pump back on again.
What should my salt generator be set at?
We suggest you start your salt chlorine generator at 50 percent output and run it for a couple of days, then check the chlorine level. In a balanced pool, a good chlorine level is 1-3 parts per million. If your chlorine levels are low, you can raise the percentage, and if it’s high you can lower the percentage.
How can you tell if your chlorinator is not working?
Test the water that water has just left the chlorinator – it should have a very high chlorine reading. (Remember that if it is extremely high it may bleach the test tablet so you may have to dilute the water you are testing). If there is no chlorine reading, the chlorinator will not be working.How do I reset my Hayward Aqua Trol salt generator?
To reset, move the switch to ‘Off’ and then back to ‘Auto’. Wait for the relay to click (5 to 10 seconds). When the instant salt level is stable (and the negative sign still present), slide switch to ‘Super Chlorinate’ and back to ‘Auto’. It takes about 30 seconds for the unit to settle back on the default reading.
How do I know if my flow switch is bad?”No Flow” light coming on probably means the cell’s flow switch has gone bad. Verify that the pump is running first (water is actually flowing through the line). If “No Flow” stays on the flow switch needs replacing. ”Flow” LED turning from green to red means water flow through the system has been disrupted.
Article first time published onHow do I reset my Hayward OmniLogic?
Shut Down – When Shut Down is selected, the OmniLogic will turn off all pool equipment and report when it is safe to remove power. When this message is displayed, you can either power off the unit or restart the OmniLogic by touching the large power button displayed on the left side of the screen.
What temperature does a Hayward salt Cell stop working?
In pool water temperatures that are 60 degrees or below, the salt generators simply shut down and by design do not allow the salt cell to ionize (breakdown) the salt and convert it to chlorine.
What happens if salt level is too high in pool?
Having too much salt in your pool water can result in unnecessarily increasing chemical expenses. But having too little salinity restricts the amount of chlorine being generated and can lead to algae and bacteria growth.
Why is my salt water pool not generating chlorine?
Salinity. Chlorine generators need salt to produce chlorine and can’t do so if the amount of salt in the water is too low. The desired salinity level in a saltwater pool is between 2,500 and 3,500 ppm. … If your salinity is below 2,500 ppm, the generator will not be able to produce chlorine.
Why are my salt generator check salt and inspect cell lights staying on?
If both the “check salt” and the “inspect cell” lights stay on, it most likely means that no chlorine is being produced at this time and your salt level fell below 2300 ppm. Both lights will also stay on if the controller is set to the wrong turbo cell type, or if the cell is unplugged.
How do I unlock my Hayward configuration menu?
Unlock Configuration Menu To unlock the Configuration Menu, repeatedly press the Menu button until “Configuration Menu” is shown in the Menu Display. Press and hold the Menu Display for 5 seconds. Refer to your pool control’s manual to determine what options are offered within the Configuration Menu.
How do I lock my Hayward configuration menu?
Press the ‘Menu’ until, ‘Configuration Menu-Locked’ appears. To unlock, press and hold the (<) & (>) until the text, on the display, changes from ‘Locked’ to ‘Unlocked’ (unit will beep).
What should my Hayward chlorinator be set at?
How much salt does the system require? Salt Systems work best with approximately 3200 parts per million (ppm) of salt, which is roughly the equivalent to a teaspoon of salt per gallon. However, all Hayward Salt Systems are designed to operate with salt levels anywhere from 2700 ppm to 3400 ppm.
What should my chlorinator read?
On a Hayward Salt Chlorinator, your salt reading should be between 2,700 – 3,400 PPM (parts per million) with the optimum level of 3,200 PPM.
How many hours a day should a salt water pool pump run?
The average pool system needs to run anywhere between 4-10 hours so you will have to gauge it yourself though testing over time.
Should chlorinator be full of water?
The saltwater chlorinator needs a sufficient flow of water for effective operation. A dirty skimmer basket, clogged or dirty filter, and a clogged pump strainer, can cause insufficient water flow for the chlorinator to produce less chlorine.
Why is my salt cell light blinking?
If the “Inspect Cell” light flashes by itself it is an early indication that the salt generator needs a manual reset. Each cell is equipped with 500 operational hours and requires a manual reset once it expires. To reset the cell, hold down the “Diagnostic” button for 3-5 seconds.
Why does my chlorinator says no flow?
The most common reason for low or no flow is that the baskets are full of debris. … *Always turn the pump off before you remove the baskets, if your pool pump is below water level you will need to close the valves in front of the pump and set the multiport valve on the filter to ‘closed’.
What does a Hayward flow switch do?
The flow switch is a safety device that ensures that water is flowing through the cell before the salt system will generate chlorine.
How do you test a flow switch?
- Put cover on the flow switch and turn power on. Video of the Day.
- Start flow through the designated system.
- Observe flow in operation to determine if flow switch is working properly.
- Repeat this process many times to ensure flow switch and designated system is in fact working accurately. Tip.
