How do I reset my Hunter XC sprinkler system

Unplug the controller’s transformer.Press and hold down the , and buttons.Plug the controller’s transformer back in.Release the , and buttons. The display should now show 12:00am. All the memory has been cleared and the controller may now be reprogrammed.

How do I reset my hunter retic controller?

Unplug the controller’s transformer.
Press and hold down the , and buttons.
Plug the controller’s transformer back in.
Release the , and buttons. The display should now show 12:00am. All the memory has been cleared and the controller may now be reprogrammed.

How do I reset my sprinklers?

Turn the control dial to the “off” position.
Press the “next” button to access the clear-memory feature. …
Press and hold the “off” button until the display stops blinking.
Turn the control dial to the “run” position.
Press and hold down the “minus” arrow and “prog” buttons simultaneously.

How do I reset my hunter core?

Turn the dial to the advanced features position. Press the down arrow to scroll to page two. Select ERASE ALL by pressing the “+” button.
Press and hold the “+” button. The display will briefly inform you to please wait and then indicate when the reset is done. 2.666665.

How do I reset my hunter X2 sprinkler?

Turn the dial to the RUN position. …
Press and hold the program button.
Press and release the RESET button located inside the lower wiring compartment. …
When the display reads the controller station count; (e.g. 14) then DONE, release the PRG button.

Why is my irrigation system not working?

If your sprinkler system is not getting water, a number of things could be the culprit: The backflow may be off. If the handle on your backflow valve gets inadvertently shut off, it restricts any water from flowing past the backflow and to the sprinkler system valves. Your rain sensor might be faulty.

How do you program a hunter XC sprinkler system?

Step 1: Set The Current Time. First, you will want to ensure that the current time is correct. …
Step 2: Set the Start Times. Next, turn the dial to “Start Times”. …
Step 3: Set the Run Time. …
Step 4: Set the Watering Days. …
Step 5: Test Coverage. …
Step 6: Finished!

How do you manually run all stations on Hunter sprinkler system?

Press and hold the button for three seconds. …
Select program by pressing the button.
Use the or buttons to select the amount of time for the station to water if different from the run time displayed.
Use the button to move to the next station.

How do you test a hunter sprinkler system?

Press and hold the PRG button. The station number will be flashing.
Press the or button to scroll to the station you would like the test program to start with. Use the and buttons to set a run time of up to 15 minutes. …
After a 2 second pause, the test program will begin.

Why is my sprinkler not turning on?

When the sprinkler zones do not turn on at all, it is generally a problem with the electrical signals running from the controller to the valve solenoids. More rarely, it is caused by a faulty valve that needs to be rebuilt or replaced.

Article first time published on

How do I know if my sprinkler solenoid is bad?

Never-ending water: The valve solenoid may get stuck open, allowing all or a trickle of water through at all times. …
Water leaks: High pressure from a broken solenoid can put a lot of stress on your sprinkler system and burst small or large leaks throughout it.

Is there an app for Hunter sprinkler system?

Hunter Hydrawise Remote access is possible through either the Hydrawise app (iOS or Android compatible devices) or online through their cloud software. Key product features include: Predictive Watering Adjustments based on web-based weather data brings up to 50 percent in water savings.

What is Hunter Solar Sync?

The Solar Sync ET sensor is an advanced weather sensor that calculates evapotranspiration (ET) and adjusts Hunter controllers daily based on local weather conditions. Solar Sync measures sunlight and temperature, and uses ET to determine the correct seasonal adjustment percentage value to send to the controller.

How do you use Hunter WIFI?

Any member of the Hunter College community (students, faculty, and staff) can use Hunter’s wireless network. Simply have your wireless device connect to the network called “hunternet”, and then open a web browser. The browser will go directly to an authentication page where you type in your Hunter NetID and password.

How do I reset my Hunter Pro HC controller?

Unplug the controller’s transformer.
Press and hold down the, and buttons.
Plug the controller’s transformer back in.
Release the , and buttons. The display should now show 12:00am. All the memory has been cleared and the controller may now be reprogrammed.

What is Seasonal Adjust on Hunter?

Seasonal Adjust can be increased so the stations run longer than the programmed time. … For example: If your Run Times in the summer are set for 1 hour and you adjust the Seasonal Adjust to 50%, your Run Times will now change to 30 minutes. To view the new adjusted run time, turn the dial to set run time’s position.

How do you test a hunter node?

Make sure the controller is in Idle Mode. Press and hold the PRG button until the icon is displayed. The station number will be displayed in the lower left side of the display along with the run time. Quickly press the plus or minus buttons to set the duration of watering time for the test program.

How do I turn my hunter node back on?

To turn the controller back on, use the center button to return to the home screen and allow the controller to go to sleep in that position. To turn your controller off, press the button until the icon and Off is displayed on screen. After a short period of time the display will shut off to retain battery power.

How do I change the battery in my hunter node?

Unscrew the rear body of the NODE body to gain access to the battery compartment.
Insert the battery/batteries into the battery tray and connect to the controller using the battery connector.
Make sure that no water is inside the battery compartment.