How do I set the time on my Hayward pool pump

This pump has it’s own timer and speed control, so you will not want to use any sort of mechanical secondary timer or control.

Does Hayward Super pump have a timer?

This pump has it’s own timer and speed control, so you will not want to use any sort of mechanical secondary timer or control.

How do I set an old Intermatic timer?

Erase all previous timer settings by sliding the control lever left to the “Off” position. …
Move the control lever to the “On” position. …
Turn the time dial clockwise until you reach the half hour that is closest to your present time. …
Press the time dial to set the present time.

How do you turn off the timer on a Hayward pool pump?

SELECT START/STOP TIME – Use the + or – buttons to select the start time. Press the > button to switch to the stop time. Use + or – to select the stop time. Press > to move to the day selection.

How do I reset my Hayward EcoStar pump?

To manually clear, shut off the breaker supplying the EcoStar with power for at least 1 minute, then restore power.

How long should I run my pool pump?

Overall, the lessons learned today is you should run your pool pump an average 8 hours a day to properly circulate and clean your water. The pump should push your entire pool in gallons in this 8 hour period of time. Residential pool water only needs to be turned over once daily to have proper filtration.

How do I lock the configuration menu on Hayward pump?

Press the ‘Menu’ until, ‘Configuration Menu-Locked’ appears. To unlock, press and hold the (<) & (>) until the text, on the display, changes from ‘Locked’ to ‘Unlocked’ (unit will beep). Press the (>) repeatedly, until ‘Chemistry Config. Wizard’ appears on the display.

How do I calibrate my Hayward Aqua Plus?

With the pump running, take the power switch down to the “Off” position, and then back up to “Auto”. You should hear a click within 10 or 15 seconds. When you do, press the diagnostic button five times in a row. The system will go through a recalibration process.

Can you put a Hayward pool heater on a timer?

We would recommend putting the heater on the same timer as your pump. You would need to hardwire both to the timer. If you run your pump on 115v, you can use timer model T101P201. If you run your pump on 230v, you can use timer model T104P201.

How do I reset my Hayward Aqua Plus?

You must reset the system by entering the ‘Diagnostic Menu’ and then hitting the right arrow key once and then pushing the plus key once. This should reset the light and message.

Article first time published on

What does chlorinator off no flow mean?

The “No Flow” light indicates that the flow switch is not detecting sufficient water passing through. Check the following: cleaning the cell or the filter (see how to backwash a DE Filter or Clean a Cartridge Filter). Replace the flow sensor.

How do you set the analog time switch?

Analog time switches are set by turning the timer dial to the desired time. Then, you need to make certain lever adjustments to set the on/off cycles. Once you connect the switch to a power source, the dial will keep time, similarly to a clock. The switch should be wired into a circuit.

How do I change the speed on my Hayward pool pump?

SELECT TIMER ONE SPEED – Press + or – to change the RPM Speed. Press > to move on to the Timer 1 start/stop time. Note: As mentioned in Step 9, you may want to test the speeds of the pump to see what speeds will be required for your pool system to function correctly.

How do you start a Hayward pool pump?

Ensure the hoses are securely attached. …
Check the skimmer water level. …
Add water to the pump basket. …
Open the air valve. …
Confirm that the necessary cleaning agent is in the filter. …
Monitor the filter’s pressure gauge and water return flow.

What is quick clean on Hayward pump?

The pump is equipped with a Quick Clean feature, which can be engaged to temporarily run at higher or lower speeds ranging from 300 to 3450 RPM. At the end of a Quick Clean cycle, the pump will automatically return to the appropriate point in its programmed schedule.

How do you troubleshoot a Hayward pool pump?

Step 1: Check the Hoses. Tighten all hose connections on the pump and filter. …
Step 2: Inspect the Pressure Gauge. …
Step 3: Check the Skimmer Basket. …
Step 4: Remove Debris. …
Step 5: Inspect the Impeller. …
Step 6: Backwash the Filter. …
Step 7: Replace the Sand or DE.

How do you set a digital pool timer?

Pull open the front flap of the timer box to expose the controls. …
Set the time and date. …
Press the “Mode” button again until you get a timer screen. …
Press “Mode” once again. …
Hit the “Mode” button one more time to save your settings and activate the timer.

Should I put a timer on my pool pump?

Swimming pool pumps should be run an average 8 hours a day to properly circulate and clean your water. … A pool timer will help you keep your pump running the proper amount of time. Again, check your pool chemical balance if you see a drastic change revert back to the old amount of time your run your pool pump.