How do I set the time on my valor plus remote

1. Press high and low flame buttons until time 6:00 flashes. 2. To set hour— press high flame button.

How do you reset Valor plus?

With a sharp object, press and hold the receiver’s reset button until you hear one short and one long beeps. Release the reset button after the second beep.

Why is fireplace beeping?

BATTERY POWER! If the batteries in the receiver are weak and cannot pick up the radio signal from the remote, the fireplace will not ignite because the gas valve will not open. … As a safety and customer convenience feature, when these batteries get weaker, an audible beep will be heard.

Why does the pilot light on my gas fireplace keep going out?

If the pilot light on your gas fireplace won’t stay lit, a very likely culprit is a component called a thermocouple. A thermocouple is a safety device and is a component of the ignition system. Its purpose is to not allow the gas valve to open if the pilot light isn’t lit.

How long will batteries last in gas fireplace?

Under normal operating conditions the batteries should last 6 – 12 months. Each of the batteries used in the hand-held transmitters should be producing 1.5V to 1.6V to operate.

How do you turn off a gas fireplace with a remote?

1. Usually there is a rocker switch that is located around your burner which, if in the “ON” position, it will override the remote. Turn the switch to “OFF.”
2. There may be a wall switch that allows you to turn your burner on. Turn the switch to “OFF.”
3. A slide switch on the receiver has been moved to the “ON” position.

How do I turn on Valor Max?

To turn on or increase light— press high flame button. To lower light— press low flame button. Turn lighting off. Press OFF.

How do I make my pilot light stay lit?

1. Make sure the thermostat is in heat mode.
2. Locate the pilot valve. …
3. Always turn the valve knob to the off position and make sure to wait at least several minutes for any residual gas to clear away.
4. Get your match ready. …
5. Once the pilot stays lit, turn the pilot valve to the on position.

How do I turn on my gas fireplace?

Turn the knob from the “Off” to the “Pilot” position. Push in the pilot knob, which manually sends gas into the system. Push the igniter button once every second until it lights. Depending on how long it’s been since the gas fireplace was last used, ignition may take multiple attempts.

Should pilot light always be on fireplace?

Should the pilot light always be on in a gas fireplace? Most gas fireplaces rely on a “continuous pilot light,” a type of pilot that remains lit so long as gas is flowing to the unit. … If you have a continuous pilot light system, you should always see a pilot flame unless you have manually turned the system off.

Article first time published on

How do I stop my pilot light from blowing out?

You should hold down on the pilot light for at least five seconds once it is lit before letting go. This will ensure your pilot light won’t blow out right after you light it.

How do I reset my electric fireplace?

SOLUTION: Turn all switches to the “off” position and unplug the unit from the wall for five minutes. After five minutes, power everything back on.

How do I stop my electric fireplace from beeping?

1. Replace the batteries in the remote (if it has one).
2. Ensure that the inlet and outlet to the heater aren’t being blocked.
3. Ensure that the fireplace components are clean and working efficiently.

Can I use a gas fireplace without electricity?

Many gas fireplaces will work without electricity. You can run both intermittent pilot ignition fireplaces and standing pilot light systems during a power outage. IPI valve systems will normally have a backup battery system in place to ignite the flames.

Can I light my gas fireplace with a lighter?

Turn on the supply line to the gas fireplace. Light a match or butane candle lighter and hold it near the burner in the fireplace. … Pull the match or light away when the burner lights. You can adjust the flame height by turning the gas key.

How does a remote control fireplace work?

Remote control gas fires work with the use of a battery operated or mains connected control valve, which responds to your battery powered remote control. You don’t have to use the remote control to operate some fires – they also come with standard controls on the appliance itself.

How does a Valor fireplace work?

Rather than directly heating the air, Valor radiant gas fireplaces emit heat through its glass and spread warmth as it is absorbed by people and furniture within a room. This is unique compared to hot air systems which simply put warm air into rooms without heating objects.

Where are Valor gas stoves made?

Valor Fireplaces rapidly grew more and more until it was time to consider moving the manufacturing from the UK to North America. As of 2001, Valor Heating and Valor Fireplaces signed an agreement allowing the Miles family to design and manufacture Valor products for both Canada and the USA.

How much is a fireplace insert?

How much does a fireplace insert cost? Most fireplace inserts and a professional installation cost about $2,000 to $4,000, depending on the state of your existing chimney and the model you select. Some electric models cost significantly less, but they offer less heat output than wood and gas fireplace inserts.

How do I turn off the pilot light on my gas logs?

Turning off your pilot light is a simple process that will save you both energy and money. All you have to do is open the front of your fireplace, turn the Pilot knob to “off,” and then turn your gas shutoff valve to the “off” position as well.