How do you change the blade on a Craftsman 42

Are Craftsman Lawn Mower Blades Reverse Thread After that, you’re ready to turn the mower on its side and get to work. Like all Craftsman Mowers, and the blade nuts are threaded standard and not reverse.

Are Craftsman lawn mower blades reverse threaded?

Are Craftsman Lawn Mower Blades Reverse Thread After that, you’re ready to turn the mower on its side and get to work. Like all Craftsman Mowers, and the blade nuts are threaded standard and not reverse.

Are lawn mower blades reverse thread?

Most lawnmower blade nuts are reverse-threaded in order to secure the blade on the drive shaft of the engine. This ensures that the blade’s rotation does not loosen the nut. However, not all blades use a reverse-threaded nut to secure them to the engine’s drive shaft.

How do I loosen a lawn mower blade?

Put a wrench socket of the correct size on the head of the bolt securing the blade to the blade holder, and apply force to the wrench handle in the counterclockwise direction to loosen the blade bolt. The bolt may have a 1/2-inch, 5/8-inch or 3/4-inch head, depending on mower model.

Are lawn mower blade bolts left or right hand thread?

The lawnmower blades itself is not threaded, but most nuts that held the blade in place are reverse threaded. The reverse thread helps to secure the blade on the drive shaft such that the rotation of the blade does not loosen the nut. It is important to note that not all lawnmowers use a reverse threaded nut.

Which side of the lawn mower blade is up?

The most common and easiest way to tell which side of your lawn mower blade is up, is to look for the label. Most manufacturers will stamp at least one side of the blade with a direction label. These can say things like: “This Side Up”, “This Side Down”, or “This Side Toward The Grass”, depending on the brand.

Are lawn mower blade bolts left hand or right hand?

The overwhelming majority of mower blade retainers (almost all are bolts) are normal right hand thread. The best indicator that the method of retaining the blade(s) might deviate from the norm would be found in the side which the grass is discharged from the mower deck.

Which way do you turn the lawnmower blade when changing?

When you tilt your mower up, this side (the one with the air filter and carb) needs to be facing upward. That’s very, very important. If the carb is facing downward, oil will make its way out of the breather tube that connects the crankcase and the air box, and you’ll end up with oil everywhere.

What size blades do I need for a 42 inch deck?

2 blades are required for a 42″ cut deck. This blade replaces Poulan/Craftsman 134149 and 532134149; Husqvarna 532 13 41-49. Blade measures 21″ long by 2-1/4″ wide with a 5 point star center hole.

How often should you replace lawn mower blades?

A good rule of thumb for the average homeowner is to replace your mower blades annually. You may also think about replacing them if they become damaged. Dig up that product manual if you want a more clear-cut answer. Always make sure to take protective measures whenever sharpening your mower blades at home.

Article first time published on

What size wrench Do I need to remove a lawn mower blade?

Dismount the mower deck from the lawn tractor to replace worn-out mower blades. Changing the mower deck’s three blades requires a 1 1/8-inch socket, box or open-end wrench for hex nuts, a block of wood and a set of new blades.

How do I know if I need a new mower blade?

It’s more than two years old. As a general rule of thumb, a mower blade should be replaced every one to two years for safety and performance purposes.
It’s bent. …
It’s dull and you’ve already sharpened it twice. …
There are dents, gouges and/or pieces missing.

Do I really need a torque wrench for lawn mower blade?

A torque wrench is critical for jobs like lawn mower blade fitting and flywheel fitting, as you already know, overtightening these components could cost you an engine.

How do you remove a stubborn lawn mower blade?

Remove a Stuck Blade with Leverage Once it’s secure, place a socket wrench over the bolt, (making sure it is the correct size), and attach the breaker bar to the socket. Use the breaker bar as the socket wrench handle and loosen the bolt. Once it is loose, unthread the bolt by hand and remove the blade.