Step 1: Set The Current Time. First, you will want to ensure that the current time is correct. … Step 2: Set the Start Times. Next, turn the dial to “Start Times”. … Step 3: Set the Run Time. … Step 4: Set the Watering Days. … Step 5: Test Coverage. … Step 6: Finished!
How do I reset my Hunter X-Core irrigation controller?
- Press and hold down the , and buttons.
- Press and release the RESET button on the right side of the controller.
- When ‘DONE’ appears on the LCD, release the , and buttons. The display should now show 12:00am. All the memory has been cleared and the controller may now be reprogrammed.
How do I turn my hunter node back on?
To turn the controller back on, use the center button to return to the home screen and allow the controller to go to sleep in that position. To turn your controller off, press the button until the icon and Off is displayed on screen. After a short period of time the display will shut off to retain battery power.
Why does my Hunter X-core sprinkler system run twice?
X-Core – Station Repeats A common reason for a controller to repeat a cycle is too many programmed start times. Only one start time per active program is required, a second start time will cycle the program an additional time.What is Seasonal Adjust on Hunter?
Seasonal Adjust can be increased so the stations run longer than the programmed time. … For example: If your Run Times in the summer are set for 1 hour and you adjust the Seasonal Adjust to 50%, your Run Times will now change to 30 minutes. To view the new adjusted run time, turn the dial to set run time’s position.
Why is my sprinkler system not turning off?
It is possible that the sprinkler valves need a good cleaning since dirt and debris can get trapped in the valve and cause problems. So, for a little DIY practice, check to see if the valves are clogged. If the valves are clean, check to see if they are cracked or broken.
Why does my irrigation system finish watering and then start again?
A common reason why a program is repeating is that you have a second start time set. The start times control the exact time your ESP-Me timer will begin to water and they also control how many times a day your timer will water. The ESP-Me allows you to set up to 6 start times per program.
How does an irrigation controller work?
The stations send electrical impulses to their respective valves to open or shut them, letting water through to the sprinklers (or not). Because this works electronically, the controller has to be physically located near enough to the valves to allow for a wired hookup.How do I switch programs in Hunter Pro C?
- Start with the dial in the RUN position.
- Press and hold the button. Turn the dial to the WATER DAYS position.
- Release the button.
- Use the and button to change program modes.
The display will show the umbrella icon flashing and On. Press the minus (-) button to bypass the sensor. … The icon will show on the display during normal operation, indicating the controller is in bypass mode. To reactivate the weather sensor press and hold the left arrow (<) button until the icon is displayed.
Article first time published onHow do you reset Hunter X2?
- Turn the dial to the RUN position. …
- Press and hold the program button.
- Press and release the RESET button located inside the lower wiring compartment. …
- When the display reads the controller station count; (e.g. 14) then DONE, release the PRG button.
How do I manually turn on Hunter nodes?
- To manually activate a program, press and hold the right arrow button until the. icon is displayed, then quickly press the PRG button. …
- To stop the Manual watering cycle press the minus button until the time is reduced to zero.
- Press the.
What is RS on Hunter SRC Plus?
The function of RS terminal was to notify the controller the status of the rain sensor. Rachio uses a different approach, Commons are dedicated to valves and rain sensor can be connected to the dedicated inputs.
What is Hunter Solar Sync?
The Solar Sync ET sensor is an advanced weather sensor that calculates evapotranspiration (ET) and adjusts Hunter controllers daily based on local weather conditions. Solar Sync measures sunlight and temperature, and uses ET to determine the correct seasonal adjustment percentage value to send to the controller.
How does Hunter Pro C rain sensor work?
A Hunter weather sensor or other micro-switch type weather sensors can be connected to the Pro-C. The purpose of this sensor is to stop automatic watering when weather conditions dictate. Remove the metal jumper plate that is attached across the two SEN terminals inside the controller.
What is seasonal adjust percentage?
Seasonal adjustment is a feature on most irrigation controllers that reduces or increases run times for all zones based on a percentage of the programmed time (Example: 10 minute run time at 50% would instead run 5 minutes). … If your controller setting is in increments of 10%, round up to the next higher percent.
