What does f11 mean on a Whirlpool Duet washer

Resolution: Error code F11 = Serial Communication Error. Error codes can be caused by a Power Surge or other electrical anomaly,attempt to return the washer to operation by following the Hard Reset procedure below. In some cases the control can be non-functioning or may not accept activation from the control panel.

How do I fix the F11 code on my Whirlpool Duet washer?

1. Check the integrity of the harness connection with the motor control panel, motor, and central control panel.
2. Analyze moving parts for worn out or broken components.
3. Check the motor control panel. Examine the main control panel of the Whirlpool washing machine. Test the engine.

What is a F11 error?

The F11 error means the keypad is shorted which is why the control panel has to be replace to fix it.

How do I fix the F11 code on my washing machine?

Unplug or turn the circuit breaker off for 10-20 minutes. Reconnect the unit to the power source by turning the breaker back on or plugging the washer back in. Press the Pause/Cancel/Stop button twice to clear the display.

What does f1 mean on a Whirlpool Duet washer?

The F01 error on this model washer means the relay for the drain pump motor on the main control board (CCU) has failed to activate or a communication error between the Central Control Unit (CCU) and the EEPROM onboard the CCU occurred.

How do I fix Fe error in Whirlpool washer?

FE Error Code This is usually the result of faulty water valve. To fix this: Close both water taps. In order to drain out any trapped water, power the washer back on, and press the spin speed button until no spin is selected, and press the START/PAUSE button.

How do you unlock a Whirlpool washing machine?

Hold down the “Control Lock” button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.

How do I put my Whirlpool Duet washer in diagnostic mode?

Whirlpool Duet Diagnostic Test Mode Close the washer door. Select any one key except “Stop/Cancel” and Control Lock. If you got it right all the lights on the Duet washer’s control should light up, and any error codes in the washer’s memory will be displayed.

What does flashing F and H on a Whirlpool Duet washer?

This error code will be displayed if the machine is trying to fill with water but the flow meter doesn’t sense any flow for 30 seconds. In this case, check the water supply to be sure you have good pressure for both hot and cold water.

What does F dL mean on a Whirlpool washer?

The F/dL code indicates a door lock error on the machine. When the door fails to lock to allow the cycle to begin, it attempts to lock itself at least six times before the error appears on the digital display screen. When the door fails to lock, the machine won’t run at all.

Article first time published on

What does F11 mean on Hotpoint washing machine?

If your Hotpoint or Indesit washing machine lights are flashing with an F11 error code or on the digital display, it is generally associated with an emptying or draining problem. If your washer is not draining properly the most likely cause is debris stuck in the filter.

Why does my washer say F?

The F indicates that the washer control detected a component problem. … If the F code was caused by excessive suds preventing the washer from draining, you may be able to shut the door and run a drain/spin cycle to remove the water from the washer.

How do you unlock a Whirlpool Duet front load washer?

1. Reach up inside the front panel and locate the door latch assembly on the right side of door.
2. Feel for a tear-drop shaped tab on the bottom of the door latch assembly. This tab will manually unlock the door.
3. Gently pull down on tab about 1/4 inch or until you hear a click.

How do you manually unlock a front load washer?

1. Turn off and unplug the washer/dryer.
2. Close the water faucet.
3. Wait until the drum has stopped rotating – never open the door while the drum is in motion.
4. Wait until water and laundry have cooled down when washing with high temperatures.

Why is my Whirlpool washer stuck on sensing?

You may unplug and plug in the washer and turn the power on. Lift and close the lid about six times within 12 seconds to reset the unit. You can also reset your washer by checking your product manual. Start a new wash cycle and test the appliance.

What is PE in Whirlpool washing machine?

PE. Of all the Whirlpool washing machine error codes, PE is one that may require a professional repair. This code usually indicates a problem with the pressure level sensor. This sensor monitors how much water is in the machine, also telling the control board if it’s been filled or emptied.

How do you read a Whirlpool dishwasher code?

You need to count the number of times the clean light flashes to find out the error code on your Whirlpool dishwasher. As an example: If the clean light flashes 5 times followed by 2 flashes (5-2) then this error is showing the function code = “Door issue” and the problem code is “The door switch is in question”.

What does Fe mean on Whirlpool dishwasher?

Whirlpool FE – WATER OVER FLOW ERROR // Water continuing to enter machine.

What is H on Whirlpool washer?

When the display shows a number up to 12, followed by an “h”, it means that the Delay Wash has been activated. Most front load washers can be set to delay the wash for up to 8 or 12 hours (depending on your model).

How do you check the pressure switch on a Whirlpool Duet washer?

1. Unplug the Whirlpool Duet washer power cord from the wall outlet. …
2. Go behind the Duet and remove the three screws securing the top panel to the rear panel with a Phillips-head screwdriver. …
3. Adjust the scale on your ohmmeter to the RX1 or X1 scale.

What does a flow meter do in a washing machine?

The flow meter measures the amount of water going into the dispenser and relays that information to the control board.

Where is the filter on Whirlpool Duet washer?

The filter on a Whirlpool Duet is located under the front kick plate. A washer filter collects lint that falls from clothes during the washing process. The lint filter should be cleaned at least once every 6 months.

How do I fix the code on my Whirlpool washer?

1. Make sure the water supply is turned on and you have proper water pressure being supplied to the machine.
2. Make sure the water supply hoses are not kinked or pinched and that screens in the supply line are clear of debris.

Why does my Hotpoint Washer say F 05?

Error code F05 on some Hotpoint (and some Indesit) washing machines means the pressure switch has “jammed” on. So the washing machine thinks it is full of water and refuses to spin. … So it waits for a signal from the pressure system so that it knows it’s safe to spin.

What does F51 mean on a Whirlpool Cabrio washer?

Washer Repair. The F51 fault code on your Cabrio washer means that the control board is not sensing the proper drive motor spin. It can either be caused by something simple, like an overloaded washer, or a faulty internal component, such as a defective motor rotor position sensor or a wiring problem within your washer.