What does HF mean on a Whirlpool Duet washer

An F20 or FH error code indicates a water supply problem. Here are some common issues: Both hot and cold water must be connected and turned on. Water inlet hoses kinked.

Why is my Whirlpool washer flashing HF?

Common solutions for: Whirlpool F/H – FH No Water Entering Machine or Pressure Switch Failure. … Check fill hoses to washer for kinks or clogged screens at water inlet valve. The manufacturer has assigned this error or fault code to indicate that there is a problem with the amount of water entering the machine.

How do I fix my FH code?

Removed pressure switch from washer.
Disassembled pressure switch., made sure all parts were in place and functional.
Reassembled pressure switch.
Tested pressure by blowing into the tube.

What is HF code for washer?

FH Error Code FH indicates that there is a Water Inlet Problem—no or insufficient water supply. Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.

What does H mean Whirlpool dishwasher?

When the display shows a number up to 12, followed by an “h”, it means that the Delay Wash has been activated. … To turn off the Delay Wash once it has been set, turn the power button off.

How do you check the pressure switch on a Whirlpool Duet washer?

Unplug the Whirlpool Duet washer power cord from the wall outlet. …
Go behind the Duet and remove the three screws securing the top panel to the rear panel with a Phillips-head screwdriver. …
Adjust the scale on your ohmmeter to the RX1 or X1 scale. …
Test the pressure switch’s “suds detect” function.

What does F2 mean on washer?

: The “F2” fault code indicates it’s taking too long to drain the tub of water in order to reset the pressure switch. The problem is that the washer is not always able to drain water so that the water level switch can reset. This can happen if the wrong type of detergent is used or if you are using too much.

Why does my washer say F 21?

If your Whirlpool washer is showing an F21 error code, this means that your washer is unable to drain properly. This can be caused by a clogged pipe, a faulty drain pump, or something simpler.

What is F20 code on Whirlpool Duet washer?

Whirlpool error code F20 appears when no water is detected entering the machine or if the pressure switch trip is not detected. The pressure switch is the part of the machine that monitors high water pressure. The washing machine automatically cancels the wash cycle during an F20 error.

How do I fix the FH code on my Kenmore washer?

Look for the “Pause/Cancel” button on the washer control panel. …
Press the “Pause/Cancel” button twice to cancel the wash cycle. …
Connect the water supply hoses back to the washer and turn on the water spigots.

Article first time published on

What does nF mean on a Kenmore washing machine?

The nF error code on a Kenmore front-load washer means that the washer isn’t filling with water. The solution is sometimes as simple as opening the water supply faucets behind the washer. Frozen water supply lines and hoses in winter also prevent the washer from filling.

How do I clear f20 code?

To reset the f20 error code, exclude the program crash of the Whirlpool washer. To do this, de-energize your washing machine for 10-20 minutes, then turn it on back. If the error disappears from the display, the problem is successfully eliminated.

What does FH mean on a Kenmore Elite washer?

The FH error code indicates that the washer control does not detect water entering the machine within 30 seconds after the fill valves have been opened. It is also displayed after 8 minutes if the flow sensor has detected 10.5 gallons passing through it without the water level pressure switch tripping.

What does H mean on a washing machine?

The number indicates in how many hours in the future, the machine will start. So in our example the machine will switch on by itself in 2 hours time. … The number indicates in how many hours in the future, the machine will start.

What does H mean on my dishwasher?

He had never seen this code but took advice and decided it stood for H2O (water). He replaced a unit on the left hand side which has an impeller with a magnet in it and a little glass tube with 2 bits of metal. The magnet should open and close these 2 bits of metal indicating water flow. Anonymous User.

What does F2 mean on my Whirlpool dishwasher?

Whirlpool gold series dishwasher error code e2/ f2, means main control board is not getting correct signal from the user interface. Turn off power/breaker, remove screws holding inner door liner, remove liner and check/secure/clean all wire connections from front interface and main control board.

What does F01 mean on a Whirlpool Duet washer?

The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes. … Be sure to unplug the washer before accessing internal components.

What does f2e2 mean on Whirlpool dryer?

The Whirlpool Duet Dryer Error E2 means the control has detected that the thermistor is shorted. This error can be a wiring issue from the control to the thermistor or a bad thermistor.

How do I fix the F2 error on my Whirlpool washer?

Press the pause or cancel button on the Whirlpool washing machine to clear the F02 error code from the display, and try using it again. …
Find the drain hose at the back of the machine, which carries the drain water from the washer to the wall.

Where is the water level pressure switch on a Whirlpool washer?

Look for the water level switch on the right side of the cabinet toward the back of the washer. The round water level switch attaches to the side of the cabinet. A rubber tube connects the water level switch to the washtub.

How do I reset my Whirlpool Duet washer?

Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

How do you bypass a water level sensor?

Let us say you have 2 lbs of clothes.
Add the 2 lbs of clothes in the washtub.
Before commencing the wash cycle, pour 4 lbs of water over the clothes and let water to soak into the fabric.
Start the wash cycle. …
You have successfully bypassed water level sensor.

Where is the water level sensor on a washing machine?

The water level switch (aka pressure switch) senses the water level in the wash tub. It does this through a plastic tube which runs from the switch in the control console down to the side of the outer tub, near the bottom . The tube is filled with air. As water enters the tub it also enters the tube.

What does F28 mean on Whirlpool washer?

An F28 error code is a common problem that means there is a communication problem with the central control unit. This problem is generally solved by essentially rebooting the control unit. Rebooting the control unit is accomplished in less than 10 minutes, even by the novice.

What does F20 mean on a washer?

F20 indicates a water inlet problem—no water or insufficient water supply.

How do I fix my Maytag F20 code?

Turn off the water and remove inlet hoses from the inlet valves in the back of the washer. Inside the inlet valves are screens. Remove any accumulated film or particles from the screens. Reinstall hoses, turn on water, and check for leaks.

What does code 5d mean on Whirlpool washer?

A Whirlpool Cabrio 5d error code means the same thing as an Sd or Sud error code; the washer is detecting too many soap suds. … Occasionally, the error code is caused by the drain pump or drain line being clogged or a defective drain pump, foam level sensor, or main control board.

How do you clear F21 code on Whirlpool Duet washer?

When the “F21” error code appears, try pressing “Pause/Cancel” to stop the current wash cycle. If water remains in the washing machine tub, touch “Drain/Spin” to force a secondary drain cycle to remove the water. Once all the water drains, try selecting a new wash cycle and pushing “Start.”

How do I reset my Kenmore Elite front load washer?

Press the “Stop” button twice, and then press the “Power” button. Video of the Day.
Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”).
Press the “Start” button to complete the reset process and restart the washing machine.

How do I reset my Kenmore front load washer?

To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a “reset” signal to all the components.