Where is drain pump located on Maytag washer

To reach the drain pump you will need to remove the access panel on the backside of the washing machine. The pump is located behind a small panel on the back, lower left side of my washer. It’s attached to the bottom frame with 3 screws. It has two hoses attached, each with one spring clamp.

Where is the drain pump on a top load Maytag washer?

The water drain pump is in the bottom of the washer, usually towards the back in top load models and the front in front load models.

Why is my Maytag washer not draining?

Drain Hose Is Obstructed An obstructed drain hose is one of the most common reasons a Maytag washer won’t drain. Both kinks and blockages can obstruct the hose, preventing proper draining. A kinked hose can be gently straightened to restore function.

Why is my Maytag washer not draining or spinning?

A top load Maytag washer not draining may have a defective lid switch assembly. On top-loading washers, draining and spinning will only occur if the lid is properly closed and activates the switch. Try depressing the lid switch with your finger to see if the machine drains and spins.

Where is the drain pump?

The drain pump is located at the bottom of your washing machine, but can be easily accessed in order to replace it if need be. If your washing machine is failing to drain during a wash cycle, it could be that there is a problem with the drain pump.

How do I know if my washing machine drain is clogged?

Observe the washing machine as it pumps water into the hoses and up into the standpipe. If you see water back up and out of the standpipe, your washer’s drain is most likely the issue. The amount of time it takes for the standpipe to fill up and overflow helps you diagnose where the clog is located.

How do I know if my washing machine drain pump is bad?

Check the pump pulley by removing the pump from the washer and trying to rotate it by hand. If the pulley doesn’t turn freely and is frozen or stiff, replace it. Also, if the agitator is moving but the tub isn’t, this is a sign the pump is dying.

How do I clean the filter on my Maytag top load washer?

The quickest way to clean out your filter is to remove it from the unit and soak it in hot water, loosening any clog or trapped residue. If the filter cannot be removed, clean it out with brush. Some filters are disposable, so instead of cleaning them you can just throw them away and put a new one in place.

How do I know if my washing machine drain hose is clogged?

The surest and most obvious sign that your washing machine’s drain hose is clogged is if you notice that the water in your machine isn’t draining away properly. Many people first notice this after putting their laundry on the spin cycle and realizing that it’s still soaking wet at the end of the timer.

What causes a washing machine not to drain and spin?

If your washer won’t drain or spin, the water level control may be faulty. Open the machine’s control panel and look for a plastic tube attached to the water level valve. If it’s clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.

Article first time published on

What causes a washing machine not to drain?

There are a few possibilities why your washing machine won’t drain. … Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.

Is there a reset button on Maytag washing machines?

Press and hold the Start/Pause button for 3 seconds. All indicator lights should be off at this point. Reset the Washer: To reset (clear) the washer, rotate the Cycle Selector Knob counter-clockwise (left) to clear any sequence.

Where is washer pump?

The pump is situated at the bottom of the washing machine and is used to pump the water from the wash, into the drain hose, to be drained away.

How much does it cost to replace a drain pump on a washing machine?

On average, expect to spend $300 to $400 for a pump replacement job. Washing machine pump repairs are usually required when you note active leaks or a tub that doesn’t drain. If the tub does not move, but the agitator does, this indicates the pump is starting to experience issues.

How much does it cost to replace a washing machine pump?

It can cost as little as $10 or as much as $75 or more. However, most homeowners pay between $25-$40 for a new pump. The other materials and tools you need include: Clamps.

Where is the P trap located?

The P-trap is a crucial element of the home plumbing system. It is the U-shaped section of the pipe located underneath the sink. Its function is to trap and hold enough water, which acts as a barrier to prevent sewer gases and odors from making their way into the bathroom.

How do you manually drain a washing machine?

Step 1: Turn off the power and lay down towels. For safety, unplug the machine. …
Step 2: Locate the drain hose at the back of the washing machine. …
Step 3: Drain the water. …
Step 1: Turn off the power and lay down towels. …
Step 2: Locate the drain hose. …
Step 3: Drain the water. …
Step 4: Scrub the filter.

How far down should a washer drain hose go?

In order for the drain hose on your Top Load washer to function properly, the drain must be at least 30″ up from the floor and less than 8 feet high. In order for the drain hose on your Front Load washer to function properly, the drain must be at least 24″ up from the floor and less than 8 feet high.

How do you unclog a main drain line?

Step 1: Loosen the cap on the drain pipe. Loosen the cap on the drain pipe. …
Step 3: Feed the auger cable into the drain pipe. …
Step 4: Run the auger until the clog is clear—and beyond. …
Step 5: Hose down the pipe and auger cable. …
Step 6: Slowly pull the auger back out of the pipe.

Does a Maytag top load washer have a filter?

Do not attempt to remove the filter while the machine is on. Washers and dryers such as those by Maytag have filters to catch lint. … The company makes both front loading and top loading washing machines of varying capacities and with differing features.

Where is the filter on a top loader washing machine?

There are 2 crescent-shaped Fine Mesh plastic lint filters in the bottom of the wash basket under the agitator. …
During drain down and spin, the water forces the lint off the bottom of the filters and down the drain.
These filters should never require cleaning or replacement.