Where is the hazard class identification number is displayed on DOT placards

The appropriate hazard class or division number must be displayed in the lower corner of a primary and subsidiary hazard label [§172.402(b)]. For classes 1,2,3,4,5,6, and 8, text indicating a hazard (e.g., “CORROSIVE”) is NOT required on a primary or subsidiary label.

Where is the hazard class found on the placard?

The hazard class number in the bottom corner of the placard must measure at least 41 mm.

Where must a hazardous materials identification number appear?

They are coded by color and contain symbols and numbers that designate the hazard class or division of the hazardous material that is being shipped. or bulk and certain non-bulk shipments, a four digit hazardous material identification number may be on the placard or on an accompanying orange panel or a white square …

Why is the identification number posted on placards?

Goods that aren’t classified or regulated by the United Nations receive North American (NA) numbers. These four-digit numbers range from 8000-9279 and are assigned by the DOT. All UN and NA placards come with an identifier that helps shippers determine the cargo’s class, division and compatibility group.

What appears on a DOT label?

DOT labels must have the hazard class number, or the division number, printed in a font that is at least 6.3 mm (0.25 inches) and not greater than 12.7 mm (0.5 inches) in height. … If the label has a green, red or blue background, the text, numbers and symbol should be printed in white.

What is hazard identification number?

Identification numbers are shown in such a way, that the upper number is indicating the danger and the lower number identifies the substances with the UN-number given in the UN Recommendations on the Transport of Dangerous Goods. …

What is a DOT Hazard Class?

The U. S. Department of Transportation (DOT) has specific rules for shipping hazardous materials. … A DOT hazardous material classification is applied if a material, in a particular amount and form, poses an unreasonable risk to health, safety or property.

What are the four sections of a DOT placard?

The square is divided into four sections, color coded: Red – flammability; blue – health hazard; yellow – reactivity/instability; White – special hazard, such as oxidizers, water reactive or Asphyxiating gas. The red, yellow and blue sections are labeled on scale of 0 to 4; 0 ‘minimal hazard’ to 4, ‘severe hazard’.

When might you display a UN number on placards?

When the primary class label for dangerous goods in transport is displayed on a tag, the UN number must also be displayed on the tag on or next to the primary class label [Subsection 4.12(2)].

How many different type placards are there showing DOT specifications?

69. How many different type placards are there showing dot specifications? 70.

Article first time published on

Which corner must display the hazard class or division number on placards corresponding to the primary hazard class of a material?

Text may be omitted from the OXYGEN placard only if the specific ID number is displayed on the placard [§172.519(b)(3)]. For a placard corresponding to the primary or subsidiary hazard class of a material, the hazard class or division number must be displayed in the lower corner of the placard [§172.519(b)(4)].

How do you label hazardous materials?

Labels must appear in their entirety and should not be placed near any other markings on the surface. They should always be visible, so never place them on the bottom of a container. If the waste has multiple hazards associated with it multiple labels should be displayed next to each other.

Where should the word hot appear if the identification number is placed on the placard?

The identification number may be displayed on a placard, or an orange panel, or a white square-on-point. If the white square-on-point is used the word “HOT” may be included in the upper corner if the HazMat is also an Elevated Temperature Material.

What is a hazard label?

The hazard label is the main communication tool for the classification of hazardous substances and mixtures. Together with the safety data sheet, the hazard label should be consistent in communicating any hazard information for a given substance or mixture to the user.

What hazards are identified in the hazard communication standard?

The SDS includes information such as the properties of each chemical; the physical, health, and environmental health hazards; protective measures; and safety precautions for handling, storing, and transporting the chemical.

What are the 9 DOT hazard classes?

Class 1: Explosives.
Class 2: Gases.
Class 3: Flammable and Combustible Liquids.
Class 4: Flammable Solids.
Class 5: Oxidizing Substances, Organic Peroxides.
Class 6: Toxic Substances and Infectious Substances.
Class 7: Radioactive Materials.
Class 8: Corrosives.

How many dot hazard classes are there?

A visor card guide for state and local law enforcement officials illustrating vehicle placarding and signage for the following nine classes of hazardous materials: 1) Explosives, 2) Gases, 3) Flammable Liquid and Combustible Liquid, 4) Flammable Solid, Spontanaeously Combustible and Dangerous When Wet 5) Oxidizer and …

What type of hazard class is 1.4 s?

Hazard class 1, division 1.4S placards meet DOT placarding specifications for explosives.

What labeling system uses United Nations class numbers?

The United Nations Globally Harmonized System of Classification and Labelling of Chemicals (GHS) – GHS Rev. 5.

What is the difference between an UN number and an ID number?

A United Nations Number – also called a UN number or UN ID – is a four digit code used to identify flammable and harmful chemicals. Non-hazardous chemicals are not given UN numbers. … In some cases, a NA number exists where a UN number has not been assigned.

What is the difference between UN and NA numbers?

United Nations (UN) Numbers are four-digit numbers used to identify hazardous chemicals or classes of hazardous materials worldwide. North American (NA) Numbers are identical to UN numbers. If a material does not have a UN number, it may be assigned an NA number.

Do subsidiary placards display a hazard class number?

The subsidiary class placard must be displayed next to the primary class placard on each side and on each end of the large means of containment: Note: A placard must NOT be displayed at a 45 degree angle on a truck frame or a supporting frame for the means of containment; it must remain as a square on point.

Can you write the UN number on a placard?

Yes. Maybe. Per 49 CFR 172.338, if more than one of the identification number markings displayed on placards, orange panels, or white square-on-points is lost, damaged, or destroyed during transportation, the carrier shall replace all missing or damaged identification numbers as soon as practicable.

How do I look up an un number?

You can either ask your employer for the UAN details or you can find out yourself, through the EPFO’s UAN portal. Go to the EPFO’s Unified Member Portal for UAN related services. Select the ‘Know your UAN status’ option under the ‘important links’ section. You will be redirected to another page.

What is the hazard class division and compatibility letter for the material?

The compatibility code consists of one letter (A–H, J–L, N, or S) that is positioned after the division number (e.g., 1.1A, 1.2C, 1.4S) and refers to the transportation and storage controls necessary to prevent potential hazards.

What size should the hazard class diamond be on the marking?

Label specifications (172.407) Each diamond-shaped label must be at least 100 mm (3.9 inches) on each side, with each side also having a solid line inner border 5.0 to 6.3 mm (0.2 to 0.25 inch) from the edge of the label.

Which column of the hazardous materials Table HMT can the identification number for the hazardous material be found?

Column 4 of the HMT lists the 4digit identification number assigned to each proper shipping name. These 4digit numbers provide quick identification of all hazardous materials.

Which placard group includes Division 1.1 1.2 explosives?

Category of material (Hazard class or division number and additional description, as appropriate)Placard namePlacard design section reference (§ )1.1EXPLOSIVES 1.1172.5221.2EXPLOSIVES 1.2172.5221.3EXPLOSIVES 1.3172.5222.3POISON GAS172.540

What placard or label is used for miscellaneous material?

White and yellow placards indicate the material is radioactive; Orange placards indicate the material is explosive; White placards with black stripes indicate miscellaneous hazardous materials.

What is the size of a hazardous materials label?

(4) When text indicating a hazard is displayed on a label, the label name must be shown in letters measuring at least 7.6 mm (0.3 inches) in height.