Which route would be automatically created when a router interface is activated and configured with an IP address? Explanation: Directly connected networks are identified with a C and are automatically created whenever an interface is configured with an IP address and activated.
Which route would be automatically created when a router interface is activated and configured with an IP address 1 multi?
Local routes are automatically created whenever an interface is configured with an IP address and activated. Destination network: The address of the remote network and how that network is connected. Outgoing interface: Identifies the exit interface to use when forwarding packets to the destination network.
What occurs next in the router lookup process after a router identifies a destination IPv6 address and locates a matching level 1 network route group of answer choices?
What occurs next in the router lookup process after a router identifies a destination IPv6 address and locates a matching level 1 network route? –The router forwards the packet. -In IPv6, all routes in the routing table are level 1 ultimate routes and contain a next-hop IPv6 address or exit interface or both.
Which routing method uses manually created routes that a network administrator enters into the router?
A static route is a form of routing that occurs when a router uses a manually-configured routing entry, rather than information from a dynamic routing ( RIP, EIGRP etc) traffic. Static routing requires a network administrator to intervene and create a route in the routing table.What is purpose of the network command when configuring ripv2 as the routing protocol?
With the network command you specify which interfaces will participate in the routing process. This command takes a classful network as a parameter and enables RIP on the corresponding interfaces. Let’s configure our sample network to use RIP. Router R1 and R2 have directly connected subnets.
How do routers route?
A router is connected to two or more data lines from different IP networks. When a data packet comes in on one of the lines, the router reads the network address information in the packet header to determine the ultimate destination.
Which route would be automatically created?
Which route would be automatically created when a router interface is activated and configured with an IP address? Explanation: Directly connected networks are identified with a C and are automatically created whenever an interface is configured with an IP address and activated.
When a router learns routes to remote networks from other routers in the network it is known as?
Dynamic Routing (1.3. Instead of depending on manually configured static routes to remote networks on every router, a dynamic routing protocol allows the routers to automatically learn about these networks from other routers.What route types are found in a router?
There are four types of routes. These types are connected route, local route, static route, and dynamic route. Automatic routing adds connected routes and local routes to the routing table. Automatic routing calculates these routes from the IP configuration of active interfaces.
What are the 3 ways routers learn paths to destination networks?- Static Routing – This is the method by which an administrator manually adds routes to the routing table of a router. …
- Default Routing – This is the method where all routers are configured to send all packets towards a single router.
What type of static route is created when the next hop IP address and exit interface are specified?
What type of static route is created when the next-hop IP address and exit interface are specified? A fully specified static route has the next-hop IP address and exit interface specified. A recursive static route has only the next-hop IP address specified.
What occurs next in the router lookup process after a router identifies a destination ipv4 address and locates a matching level 1 network route?
All hosts and router interfaces are configured correctly. … What occurs next in the router lookup process after a router identifies a destination IPv6 address and locates a matching level 1 network route? The router forwards the packet. Match the routing table entry to the corresponding function.
What happens to a static route entry?
The static route is removed from the routing table. The router polls neighbors for a replacement route. The static route remains in the table because it was defined as static. The router automatically redirects the static route to use another interface.
Which command will display which routes the RIPv2 router is advertising?
If you want to see live RIP advertisements, you can use the debug IP RIP command. You can see how in this example for router A the router is sending advertisements on both interfaces to a broadcast destination. It is also receiving updates coming from B on 10.1. 1.2 through the serial interface.
On which router would a default static route be configured?
On which two routers would a default static route be configured? (Choose two.) Explanation: A stub router or an edge router connected to an ISP has only one other router as a connection. A default static route works in those situations because all traffic will be sent to one destination.
What is static route in networking?
Static routing is a form of routing that occurs when a router uses a manually-configured routing entry, rather than information from dynamic routing traffic. … Unlike dynamic routing, static routes are fixed and do not change if the network is changed or reconfigured.
What is the purpose of setting the passive interface command on a router's interface while using ripv2?
Starts the RIP routing process. Sets the interface as passive, meaning that routing updates will not be sent out this interface. NOTE: For RIP, the passive-inter-face command will prevent the inter-face from sending out routing updates but will allow the interface to receive updates.
What command would be used to configure a static route on R1 so that traffic from both LANs can reach the 2001 DB8 1/4 ::/ 64 remote network?
What command would be used to configure a static route on R1 so that traffic from both LANs can reach the 2001:db8:1:4::/64 remote network? Answers Explanation & Hints: To configure an IPv6 static route, use the ipv6 route command followed by the destination network.
What do the routing tables of a router keep track of?
A routing table is a database that keeps track of paths, like a map, and uses these to determine which way to forward traffic. … With hop-by-hop routing, each routing table lists, for all reachable destinations, the address of the next device along the path to that destination: the next hop.
What does IP route do?
IP Routing is an umbrella term for the set of protocols that determine the path that data follows in order to travel across multiple networks from its source to its destination. … The IP Routing protocols enable routers to build up a forwarding table that correlates final destinations with next hop addresses.
How does routing work with IP?
IP Routing describes the process of determining the path for data to follow in order to navigate from one computer or server to another. A packet of data traverses from its source router through a web of routers across many networks until it finally reaches its destination router using a routing algorithm.
How are routing paths determined?
To determine the best path, the router searches its routing table for a network address that matches the destination IP address of the packet. … This means that the destination IP address of the packet is a host address on the same network as the interface of the router.
Which command is used to activate a router interface?
To enable an interface, it must be activated using the no shutdown command. (This is similar to powering on the interface.) The interface must also be connected to another device (a hub, a switch, or another router) for the physical layer to be active.
Which router is created table automatically?
These Routing tables can be maintained manually or dynamically. In dynamic routing, devices build and maintain their routing tables automatically by using routing protocols to exchange information about the surrounding network topology.
What is adaptive and non adaptive routing?
In adaptive routing algorithm, the routing decisions are made based on network traffic and topology. Whereas in a non-adaptive routing algorithm, the routing decisions are not made based on network traffic and topology. … While in non-adaptive routing algorithm, the routing decisions are static tables.
How do routers learn about remote networks?
A router can learn about remote networks in one of two ways: Manually – Remote networks are manually entered into the route table using static routes. Dynamically – Remote routes are automatically learned using a dynamic routing protocol.
When a router learns that multiple paths are available?
When a router learns that multiple paths are available to a destination network from the same routing protocol, the route with the lowest metric is put into the routing table to forward packets toward that network. The output of the show ip route command contains the following entry: S 10.2.
Which router decides about the route based on the latest routing information gathered from connected routers?
RIP version 2 launch the routing tables in every interval of 30 seconds thus lots of bandwidth is utilized in this process. It utilizes the multicast address 224.0. 0.9 to launch routing information. EIGRP (Enhanced interior gateway routing protocol): It is a progressive type of distance vector protocol.
Which is the default route in a routing table?
The default route is generally the address of another router, which treats the packet the same way: if a route matches, the packet is forwarded accordingly, otherwise the packet is forwarded to the default route of that router.
How does default route work?
A default route is the route that takes effect when no other route is available for an IP destination address. If a packet is received on a routing device, the device first checks to see if the IP destination address is on one of the device’s local subnets.
Where is default route setup?
- Enter global configuration mode. device# configure terminal.
- Enter 0.0. 0.0 0.0. …
- (Optional) Enable the default network route for static route next-hop resolution. …
- (Optional) Configure next-hop recursive lookup to resolve the next-hop gateway.
